powder coating
Application Methods For Powder Coating
By Chris Shannon
Applying powder is reasonably simple and, providing you have access to the following equipment, is something that most practical people can learn. You will need: a powder gun, a supply of clean dry compressed air, an electrical supply and the powder for spraying.
Powder is sucked from the container, which can be the manufacture's box or a hopper, depending on the type of equipment, via a powerful pump. In order to get a constant smooth flow two methods are used: vibration and fluidisation. Vibration helps to keep the powder level towards the suction tube; fluidisation enables the powder to flow through the pump easily.
The powder is sucked vertically from the container to the pump where it is passed along the powder tube; this can vary in length but is usually around three meters. The powder will then enter the gun body. The manual gun is shaped for ease of handling and comfort and will usually allow the powder to enter at the bottom of the handle. On automatic equipment the powder will usually enter from the rear as the gun body will be straight.
There are many types and variations of application equipment to suite specialised methods of application but the main two main types of gun in common use are Tribo charge and Corona charge. Both rely on the powder getting an electrical charge that in turn enables the materiel to attract to the surface of the object to be coated.
Tribo charge relies on the powder passing along the pipe and through specialised plastics in the gun body in order to create friction. The surfaces of the powder attract opposite polarity charges that in turn attract each other, even after separation. This method is, however, limited to certain types of powders.
Corona charge relies on an electrical charge at very high voltage (up to 100kv) to be released into the powder cloud at the point it is released from the gun. The charge is relayed to the gun via a low voltage (10-12v) cable and then the voltage is multiplied in the gun handle to the very high voltage required. This is then discharged into the powder cloud at the point of exit. The powder on this type of equipment will also pick up a certain amount of tribo charge along its route, so will enable this type of equipment to be the preferred choice for most coaters.
The fully charged powder will now exit the gun in a fine dust cloud and will be attracted to anything that is able to accept a charge from a distance of around 100 - 300 mm; this then remains as a powder on the surface of the component until cured. The curing process will be discussed in further articles.
Chris Shannon has been involved with both the practical and technical coating of metals and plastics throughout his adult life working for trade coating organisations throughout the midlands.
Chris Shannon, General Manager, Vistaplan International, 5 High March, Daventry, Northamptonshire, NN11 4QE, UK http://www.vistaplan-arand.com
[mailto:enquiries@vistaplan-arand.com]enquiries@vistaplan-arand.com
Article Source: http://EzineArticles.com/?expert=Chris_Shannon
Related Resources
By Chris Shannon
Applying powder is reasonably simple and, providing you have access to the following equipment, is something that most practical people can learn. You will need: a powder gun, a supply of clean dry compressed air, an electrical supply and the powder for spraying.
Powder is sucked from the container, which can be the manufacture's box or a hopper, depending on the type of equipment, via a powerful pump. In order to get a constant smooth flow two methods are used: vibration and fluidisation. Vibration helps to keep the powder level towards the suction tube; fluidisation enables the powder to flow through the pump easily.
The powder is sucked vertically from the container to the pump where it is passed along the powder tube; this can vary in length but is usually around three meters. The powder will then enter the gun body. The manual gun is shaped for ease of handling and comfort and will usually allow the powder to enter at the bottom of the handle. On automatic equipment the powder will usually enter from the rear as the gun body will be straight.
There are many types and variations of application equipment to suite specialised methods of application but the main two main types of gun in common use are Tribo charge and Corona charge. Both rely on the powder getting an electrical charge that in turn enables the materiel to attract to the surface of the object to be coated.
Tribo charge relies on the powder passing along the pipe and through specialised plastics in the gun body in order to create friction. The surfaces of the powder attract opposite polarity charges that in turn attract each other, even after separation. This method is, however, limited to certain types of powders.
Corona charge relies on an electrical charge at very high voltage (up to 100kv) to be released into the powder cloud at the point it is released from the gun. The charge is relayed to the gun via a low voltage (10-12v) cable and then the voltage is multiplied in the gun handle to the very high voltage required. This is then discharged into the powder cloud at the point of exit. The powder on this type of equipment will also pick up a certain amount of tribo charge along its route, so will enable this type of equipment to be the preferred choice for most coaters.
The fully charged powder will now exit the gun in a fine dust cloud and will be attracted to anything that is able to accept a charge from a distance of around 100 - 300 mm; this then remains as a powder on the surface of the component until cured. The curing process will be discussed in further articles.
Chris Shannon has been involved with both the practical and technical coating of metals and plastics throughout his adult life working for trade coating organisations throughout the midlands.
Chris Shannon, General Manager, Vistaplan International, 5 High March, Daventry, Northamptonshire, NN11 4QE, UK http://www.vistaplan-arand.com
[mailto:enquiries@vistaplan-arand.com]enquiries@vistaplan-arand.com
Article Source: http://EzineArticles.com/?expert=Chris_Shannon
Related Resources
Powder Coating
Fully Automated Line No job too small. Fast Turnaround
Sponsored by: www.AAGlobalind.com/ • Found on Ads by Google
Columbia Coatings
Powder Coatings And Equipment With Custom and Hard to Find Colors
Sponsored by: www.columbiacoatings.com/ • Found on Ads by Google
Powder coating - Wikipedia, the free encyclopedia
Jan 16, 2009 ... Powder coating is a type of dry coating, which is applied as a free-flowing, dry powder. The main difference between a conventional liquid ...
en.wikipedia.org/wiki/Powder_coating • Found on Google, Yahoo! Search
Powder Coating Companies
Compare powder coating booth suppliers. Read our purchasing advice.
Sponsored by: www.B2B-Exchange.com • Found on Ads by Yahoo!
Powder Coating Ovens
Custom Powder Coating Ovens No Concept Or Design Is Too Complex
Sponsored by: www.EpconLP.com/ • Found on Ads by Google
Click here to post a Free Classified
<< Homepowder coating